Machines

INDEX automates tool changes on the turret

November 2026

All the versions of this article: [Deutsch] [English]

INDEX automates tool changes on the turret
New INDEX interface enables reliable tool changes using a robot or motorised milling spindle.

INDEX is expanding the possibilities for low-staffing setups: a new interface enables automatic tool changes on the turret. Two solutions are available – using a robot in the iXcenter or, on turn-mill centres, the motorised milling spindle. The base holder remains in the turret; only the cutting head is replaced.

Until now, the automation of a turning machine or turn-mill centre has reached its limits when tools in the turret wear out or break. Replacing them has long been a manual task. Although some automated solutions are now available, they all focus on changing the entire tool holder in the turret. “Far too complicated and cumbersome,” says Dr Dirk Prust, Managing Director Technology of the INDEX Group. “That is why we have developed a new interface that makes automated tool changes on the turret simple and cost-effective.”

The INDEX solution, first presented at the Open House and AMB 2026, leaves the turret’s VDI interfaces unchanged. The key is an additional base holder inserted into the VDI interface. This tool holder is available in straight, right-angle or left-angle versions, with driven or static tooling. It features a universal HSK-A40 or HSK-T40 interface into which the tool – just the small, cost-effective cutting head – is inserted and from which it is removed. The HSK base holder has an actuating screw that operates a clamping and release mechanism for the HSK tool. “The changeover process is ideally suited to automation and takes only around 20 seconds,” emphasises Dirk Prust. The VDI interface with INDEX’s proprietary high-precision W-serration, combined with the inherently precise HSK interface, ensures a high level of accuracy.

A robot performs automated tool changes on the turret, providing the basis for reliable setups with minimal operator involvement.

The robot takes care of tool changes
INDEX offers two automation options. On single-spindle turning machines equipped with an iXcenter, the robot installed in the cell can insert tools into and remove them from the turret. For this purpose, it is fitted with an end effector that is either permanently mounted on the robot or interchangeable via an automatic quick-change interface. Equipped with a gripper and a torque-controlled screwdriver, it can remove the tool to be replaced from the HSK base holder in the turret. First, it turns the screw in the holder to actuate the clamping and release mechanism for the HSK tool. Once the tool has been removed, replaced and clamped again, it is immediately ready for use with an accuracy of less than 5 µm, including the coolant supply.

On INDEX turn-mill centres, the motorised milling spindle can perform tool changes on the turret without an additional robot cell.

Tool changes using the motorised milling spindle
An INDEX turn-mill centre equipped with tool turrets and a motorised milling spindle does not even require a robot cell for automated tool changes. Instead, the motorised milling spindle can perform the changeover. Here too, the prerequisite is a set of base holders with HSK-A40 or HSK-T40 interfaces fitted into the turret’s VDI interfaces.

To remove a tool from the turret, the motorised milling spindle picks up an empty gripper unit, also equipped with a screwdriver, from the magazine via its HSK-A63 interface. The gripper engages with the tool to be replaced in the turret. The screwdriver loosens the locking screw, and a 90-degree position prevents the tool from falling out. The motorised milling spindle then returns the gripper unit and the worn tool to the magazine.

The gripper unit with its integrated screwdriver enables the tool to be released, removed and inserted into the base holder.

A new tool is inserted in a corresponding sequence: the motorised milling spindle picks up a gripper holding a new tool – a cutting head with an HSK-A40 interface – from the magazine. It then swivels towards the turret to insert the tool into the HSK interface of the base holder and tighten the securing screw. The tool locks automatically as the T-nut rotates. The screwdriver stops at a defined torque and angle before returning to a zero-degree position. This allows the motorised milling spindle to disengage the gripper from the tool and return it to the magazine empty.

The automatic tool-changing system developed by INDEX provides the basis for autonomous, reliable tool changes on the turret. Machining cannot take place during the changeover. However, automatic replacement can reduce downtime when worn tools would otherwise have to be changed manually.

www.index-group.com

The Eurotec Newsletter

© 2026 EUROTEC - ALL RIGHTS RESERVED.