Ten years ago, the NASA rovers Opportunity and Spirit landed on Mars. It keeps going and going and going. "It is equipped with maxon brushed DC motors" the company proudly announced recently.
Ten years ago, the NASA rovers Opportunity and Spirit landed on Mars. It keeps going and going and going. "It is equipped with maxon brushed DC motors" the company proudly announced recently.
Today, Opportunity is still exploring Mars – an unbelievably long time, considering the robot was only designed to last about 90 days. It has covered a distance of approximately 39 kilometers so far and continues to roam around a vast area. On board, 39 maxon brushed DC motors can be found.
On January 25, 2004, the Mars rover Opportunity landed in the Eagle crater. Since then, it has been investigating the planet for NASA (National Aeronautics and Space Administration), a USA agency responsible for the exploration of space. It has examined a number of craters, dunes, and flats, always searching for traces of water. It did not take long before Opportunity found first indications (sediment structures, minerals) that there used to be water on Mars. The Mars rover is able to take photos, brush the ground and drill into stone and it continues to do so today. “The rover is in exceptionally good condition for its age”, says John Callas, a manager at NASA. However, things haven’t always been easy for the rover in the past ten years. Its wheels have become stuck in the sand requiring a very difficult maneuver to release them once again. Sand storms disabled the solar panels and prevented the batteries from recharging. Opportunity is now starting to show a few small symptoms of aging: the 185 kg robot has a bit of “memory loss” – every now and again, its hard disk shows signs of wear caused by the long period of use.
39 km and 39 maxon drives With drives manufactured by maxon motor, Opportunity has been able to safely navigate the surface of Mars for ten years. The rover contains a total of 39 brushed DC motors that are all still operating reliably. They are used to drive the robotic arm, the Rock Abrasion Tool (RAT), the cameras, the control mechanism and the wheels of the rover. The motors are standard products with diameters of 20 to 25 millimeters and an efficiency of over 90 percent. Minor modifications were necessary to adapt the DC motors for the harsh environmental conditions: the temperature on the surface of Mars fluctuates between approximately -120 °C and +25 °C.
This speaks about reliability of maxon motors (as well as all other pieces of equipment on the robot) indeed, but also about human genius. We at Eurotec haven’t thought to use Opportunity to spread the microtechnology messages of our customers to the red planet!
.
.
.
...brought to you by Eurotec-Online.com
Robots from Stäubli can now be directly operated with B&R controllers. This is possible thanks to a Powerlink interface on Stäubli’s uniVAL drives that allows Generic Motion Control programs from B&R controllers to be transferred to the robots. In this way, robotics engineers can use the uniform programming and operating environment provided by B&R controllers. The easy integration of Stäubli robots is guaranteed using uniVAL drives and Powerlink networks. Robots are connected (…)
What is the common point between the first robot controlled by a PC (with Windows 95, as many would say : prehistory), the 4d simulator installed at Walt Disney’s Epcot® Park Florida, a global network of training in robotics and your car? They are all related to the Kuka Roboter company. And if we are far from the 1950s science-fiction stories and their humanoid robots (which are sometimes in revolt), reality is no less surprising. Meeting at Kuka Roboter Switzerland with Ms Meike Stuber, in (…)
Again several Kuka robot received the world-renowned "red dot" award this year. Three products of the Bavarian industrial robot provider were among the winners: the KR 5 arc, HW and KR 700 PA have been awarded by the red dot. The KR 5 arc was even awarded as the best of the best red dot and honored for outstanding design achievements. During a solemn Gala on July 5, 2010 in the Essen Aalto Theatre the industrial designer Mario Selic and a Kuka developer team received the prestigious award (…)
For the second time this year at Automatica Fanuc awarded the prices of Robotics. With these awards, the robots manufacturer rewards partners who are distinguished by their exceptional achievements and their exemplary commitment. In the general industry category, Fanuc Robotics award was given to Robotec Solutions AG. This integrator works exclusively with Fanuc robots and technologies. He is also known for its planning and careful implementation and the professionalism of its work. These (…)
The simplest way of controlling robots. Touch screen. Graphics support. Flexible interaction. The more powerful the capabilities of the robots become, the more intuitive user interfaces for operator control of the robots are pushed into the foreground. The new KUKA smartPAD brilliantly demonstrates, on a large, high-resolution, antireflection touch screen, how robots can be operated intuitively. . Operations are presented to the user in a transparent manner by means of intelligent, (…)
At Siams KuKa presents a small assembly and manipulating cell. Combining a linear axis to the capacities of a scara R550 robot, this cell is ideal to manipulate small parts like needed in watch industry or microtechnology. The KR 5 scara R550 has a reach of 550 mm with a payload of 5 kg and a high positioning accuracy of under 0.02 mm. The Kuka Scaras combine fast and best-selling scara manipulators with very dependable and best-selling PC-based robot controller. And the linear axis… The (…)
Stäubli Robotics, manufacturers of innovative and technologically advanced industrial and cleanroom robots, announces the introduction of the new TS series of high speed SCARA robots. This next generation robotic line features 100% Stäubli design and engineering, and are among the fastest commercially available SCARA robots in the industry. . Stäubli’s high performance benchmarks of speed, rigidity and precision are exemplified by this series which includes the TS40, TS60 and TS80 with (…)
Designer and integrator of robotized automation solutions for the German speaking countries, Robotec Solutions AG wishes now develop its activities towards French speaking areas. To sustain this strategy, the company can count on Dominique Lalut. Benefitting from a more than 25-year know-how with the most important robots manufacturers in the world, this French native is well known in the French speaking Switzerland industries and joined the sales team of Robotec Solutions AG. From now on, (…)
© 2026 EUROTEC - ALL RIGHTS RESERVED.