Ten years ago, the NASA rovers Opportunity and Spirit landed on Mars. It keeps going and going and going. "It is equipped with maxon brushed DC motors" the company proudly announced recently.
Ten years ago, the NASA rovers Opportunity and Spirit landed on Mars. It keeps going and going and going. "It is equipped with maxon brushed DC motors" the company proudly announced recently.
Today, Opportunity is still exploring Mars – an unbelievably long time, considering the robot was only designed to last about 90 days. It has covered a distance of approximately 39 kilometers so far and continues to roam around a vast area. On board, 39 maxon brushed DC motors can be found.
On January 25, 2004, the Mars rover Opportunity landed in the Eagle crater. Since then, it has been investigating the planet for NASA (National Aeronautics and Space Administration), a USA agency responsible for the exploration of space. It has examined a number of craters, dunes, and flats, always searching for traces of water. It did not take long before Opportunity found first indications (sediment structures, minerals) that there used to be water on Mars. The Mars rover is able to take photos, brush the ground and drill into stone and it continues to do so today. “The rover is in exceptionally good condition for its age”, says John Callas, a manager at NASA. However, things haven’t always been easy for the rover in the past ten years. Its wheels have become stuck in the sand requiring a very difficult maneuver to release them once again. Sand storms disabled the solar panels and prevented the batteries from recharging. Opportunity is now starting to show a few small symptoms of aging: the 185 kg robot has a bit of “memory loss” – every now and again, its hard disk shows signs of wear caused by the long period of use.
39 km and 39 maxon drives With drives manufactured by maxon motor, Opportunity has been able to safely navigate the surface of Mars for ten years. The rover contains a total of 39 brushed DC motors that are all still operating reliably. They are used to drive the robotic arm, the Rock Abrasion Tool (RAT), the cameras, the control mechanism and the wheels of the rover. The motors are standard products with diameters of 20 to 25 millimeters and an efficiency of over 90 percent. Minor modifications were necessary to adapt the DC motors for the harsh environmental conditions: the temperature on the surface of Mars fluctuates between approximately -120 °C and +25 °C.
This speaks about reliability of maxon motors (as well as all other pieces of equipment on the robot) indeed, but also about human genius. We at Eurotec haven’t thought to use Opportunity to spread the microtechnology messages of our customers to the red planet!
.
.
.
...brought to you by Eurotec-Online.com
The TKX allows for the production of small series and individual pieces economically, using a Faulhaber motor in the electric drive of the automatic changer. The range of tasks that is being carried out by robots has become limitless. It includes gripping, holding as well as manipulations such as clamping and screwing through to foaming and welding. And when it comes to standardized mass production, specialized robots can be used, which perform the same tasks day and night. But many (…)
Yamaha Robotics SMT Section has revealed its latest inline solder-paste inspection system, the VP-01G-Y, with advanced features to raise surface-mount production quality and productivity. Consolidating high-speed and high-resolution inspection capabilities in a single unit, the VP-01G-Y uses advanced algorithms in 2D and 3D modes to aid focusing and contour extraction. Analysis includes 3D solder-paste and adhesive inspection, foreign-matter detection, and board warpage, to assist (…)
Over one hundred ABB GoFa™ collaborative robots automate laboratory workstations, accelerating R&D in the chemical and life sciences sectors. ABB Robotics and XtalPi have entered a strategic partnership to produce a range of automated laboratory workstations in China. The new, automated laboratories will boost the productivity of R&D processes in biopharmaceuticals, chemical engineering and chemistry, and new energy materials. XtalPi is dedicated to driving intelligent and (…)
These cobots introduce advanced hardware, more safety features and certifications, and next-generation configuration capabilities, making them easier to use than ever before. Responding to manufacturers’ needs for enhanced performance and safety in human-collaborative settings, the TM S Series offers four models, with payload capabilities from 5 kg to 14 kg and reach from 700 mm to 1300 mm. Various mounting types are possible, including use on a mobile robot to create a mobile manipulator (…)
Universal Robots’ larger, much-anticipated new UR20 cobot is ready to generate sparks at FABTECH, North America’s biggest metal forming, fabricating, welding and finishing event, taking place Sept. 11-14 in Chicago. The new cobot, that brings 18” of additional reach radius (36” diameter increase), greatly broadens the range of weldments that will be achievable in a given fixture setup, says Josh Pawley, co-founder of Universal Robots (UR) partner, Vectis Automation: “Vectis Automation is (…)
Industrial robots have become indispensable in modern production. They can lift heavy loads, perform precise work and produce at a high speed. But that’s not all: thanks to advanced technology and the integration of microproduction and vision systems, industrial robots are now capable of handling even more complex tasks. In the field of microproduction, for example, industrial robots can manufacture even the smallest parts and components. Here, high precision and repeatability are (…)
Faced with a complex automation challenge, Bruderer Maschninen Fabrik in Frasnacht found an innovative solution with the system integrator Roth Technik and Fanuc. BRUDERER builds highly accurate stamping machines for a worldwide market with a nominal force of 180 to 2500 kN and a stroke rate range of 100 to 2000 rpm. Their machines are used to produce parts used in watches, electronics, and a variety of other industries. The automation challenge was to load blanks into and remove (…)
The Bosch Rexroth company was presented with the prestigious industrial prize, the HERMES AWARD, at the opening ceremony of HANNOVER MESSE by Bettina Stark-Watzinger, Federal Minister of Education and Research, in the presence of German Chancellor Olaf Scholz. This year the jury, chaired by Prof. Dr.-Ing. Reimund Neugebauer, President of the Fraunhofer Society, awarded the prize for a product geared to the dynamic robotics market. As one of the three nominees, the Smart Flex Effector (…)
"Alors on danse" has brought him worldwide fame. Now Stromae is continuing his Multitude tour in Europe from March to December 2023. Also on stage: Ten KUKA robots that move oversized LED screens. A video that has now been released shows how this spectacular stage set came about. "The stars of this show are obviously the robots," Stromae pointed out in an Instagram video in July 2022, "they were the main inspiration of this show." Ten robots – five hanging from the ceiling, five standing (…)
Once the preserve of high-volume operations at automotive plants, we´re today finding that robots are infiltrating all sectors of the commercial world. Even beyond traditional manufacturing, inspection and packaging operations, we see robots fulfilling tasks that extend from mining and space exploration, through to surgery and laboratory research, and even fruit picking. With such a vast repertoire of applications, the robots of today need one principal attribute: flexibility. Much of this (…)
© 2026 EUROTEC - ALL RIGHTS RESERVED.